Images
SL 30

Slicer Selectra SL 30

SL 30 offen

Slicer Selectra SL 30, open

Sl 30 + GBK 220

All Selectra slicers are optimally suited for combination with the GHD packaging machines.

Öl unten

Optional: Lower lubrication of the band knives for mixed loaves with up to 40% rye content.

Beölung oben

Optional: Upper lubrication of the band knives for mixed loaves with more than 40% rye content.

Beölungsaggregat

Optional: Lubrication unit - Patented, oil mist-free knife lubrication system for precisely metered, finest lubrication of the band knives.

Messerführung

Blade guides: The self-supporting drum suspension allows quick changeover and optimum access to cleaning and maintenance.

Outfeed

Outfeed: Infinitely variable speed and thus synchronizable with the packaging machine.

Standard specification

Welded machine frame, lacquered in stainless steel design colour, standard
Hinged door at the outfeed side
Panels, doors and electrical cabinet or switchbox made from stainless steel
Cover panels with hasp locking
Protection hoods made of polycarbonate
Slides and/or funnels for bread crumbs
Footrests without dowel holes
Band-blade drive 5,5 kW
Conveyor system with adjustable speed
Accumulating belt in front of the Infeed, plastic roller carpet Azetal
Slicer - Bottom infeed: Plastic slat conveyor belt, products between 160 -400 mm
Product infeed with lateral guides, driven adjustable
Slicer -Infeed: Side guiding by driven belts
Slicer -Upper infeed by belt, products between 160 - 400 mm
Top belt height, driven adjustable
Slicing compartment with additional sensors with mechanical safety locking for openings
Equipment stops in case of blade break
Pneumatic blade tensioning device with automatic tension regulation
Blade guides with hardened round fingers for one constant slice thickness
Set of band blades 18x
Spare set of band blades 18x
Lower pulley, standard
Slicing with dry blades
Catching tray for crumbs below slicing compartment, extendable drawer, stainless steel
Crumb scraper, pneumatic activated, installed at both drums
Illumination of the working area inside the machine
Plate at the infeed side of the slicer Outfeed
Slicer-Outfeed equipped with chain conveyor with pusher bars, base plate made from structured stainless steel.
Product outfeed with lateral guides, manual adjustable by handwheel
Catching tray for crumbs below outfeed position, extendable drawer, stainless steel
Signal lamp - red / green
Signal horn
Switch cabinet with hasp locking
Switch cabinet with fan+filter system - standard-
Operating elements located in the machine panel or door of the switch box
Controls + touchpanel Omron
Frequency converter Hitachi (Omron)
Automatic Stand-By control system for behind located machines in case of missing products
Electric execution according to CE-specification
Operating language and labels in German language
Operating manual in German language
Documentation in German language
Options

Welded machine frame, lacquered in stainless steel design colour. Clean room stage 1 - freely air flow
Welded machine frame, stainless steel, standard (supporting tube for drums made of galvanised steel)
Sliding door at the outfeed side (included in clean room stage 2/4/5)
Protection hoods made of perforated stainless steel panels
Protection hoods for clean room stage 5 - Full housing with clean air funnel
Band-blade drive 7,5 kW
Band-blade drive 11 kW
Transport for bread loaves into the by-pass, pusher system installed above the slicer feeding system
Chain conveyor for automatic transport of full bread loaves into the slicer outfeed
Accumulating belt for product feeding in front of the Infeed, total length 2,7m with foldable length 1,5 m, plastic roller carpet (Azetal)
3 Sensors to detect twisted products - installed above the transport system
Additional set of hardened blade guides with hardened round fingers for one constant slice thickness
Storage Trolley - Space for up to 5 additional sets of blade guides
Oiling system for band blades close to the lower pulley incl. oil pump, up to 40% rye content
Twin -oiling system for band blades close to the upper pulley and close to the lower pulley, incl. oil pump, more than 40% rye content
Blade sterilization by 2 UV-light radiators (Brand SterilAir, ET2230-4NA, Dose approx. 22-33 mW/cm²)
Non-stick coating for machine components which get in touch with the product
Refuse of endpieces / heels. Adjustable plate in front of the slicer Outfeed
Clean room stage 3/4/5: Crumb suction at the outfeed, guide plates and collecting funnel inside the slicer for crumbs and endpieces. Vibrating slide with channel for bread crumbs installed in the upper slicing housing. Pipeworks up to the central connection point for connection to local suction system
Switch cabinet with service interface FrontCom® with LAN and power socket
Additional signal lamp
Switch cabinet with locks + keys
Switch cabinet with air-conditioning
Comfort-operating panel, rotatable with support arm system
Controls + touchpanel Siemens
Controls + touchpanel Allen Bradley
Control unit with OPC-UA, customer-specific data supply
Frequency converter SEW inside the switch cabinet
Frequency converter Allen Bradley
Potential-free contacts for circuit signaling with local components
Remote service, VPN-Switch INSYS , (Master unit)
Voltage modulation, 3-phase
Overvoltage protection
UL- certificate / UL-c certificate and labeling before delivery at GHD Hartmann
Electric execution according to UL-specification
Customer-specific special machine modifications
Customer-specific operating language and labels
Customer-specific operation manual
Customer-specific documentation
SL30 layout
SL30-Kombinationen
SL30 + EC101IS
BS20-Linie
LVS System mit CP+SL30+GBK420

Can the machine be cleaned wet?

The machines are designed according to protection class IP54. Wet cleaning of the machines inside the cutting and packaging room is not recommended as moisture and bread crumbs directly cause the formation of mold spores.

Wet cleaning should therefore only take place outside the cutting and packaging room: components of the machine, such as guide plates, can be dismantled and cleaned at an external washing area. After drying and disinfection, the hygienically flawless dry components can be inserted into the device and reused.

Change kits allow cleaning and preparation in addition to the production operation.

Can different slicer band blades be used?

In a tape cutter slicer band blades of the same manufacturer with the same pitch and shape are always used. Complete sets are always interchangeable. If very different types of bread are cut, different sets of knives make sense.

Are brochures in other languages available?

Further brochures in other languages ​​are available here. The technical state may not be updated!

How can I determine the size of bags?

Bag sizes depend on the products and the orientation of the products in the bag.

In any case, the product tolerances must be considered. This is especially important when several products are packed side by side, one after the other or one above the other in a single package. A beautiful packaging fits as closely as possible to the product and supports the product. The sizes recommended by GHD Hartmann can be looked up in an Excel spreadsheet.

Is it possible to combine a GHD Hartmann Schneider with other packaging machines?

Of course, our bread slicers can not only be combined with capping and packaging machines from GHD Hartmann, but also with machines from other manufacturers.

Take advantage of our many years of experience for optimum coordination and connection.

How loud is a machine by GHD Hartmann?

The noise emission initially depends on the type of machine. Packaging machines, cutters or systems for grouping are fundamentally different due to the different functions.

Another factor is the nature of the products, which can behave differently during processing and transportation. A machine may be very quiet at idle, but produces varying amounts of noise during processing, depending on the products.

The type of cover also has a great influence on the noise emission: Polycarbonate viewing covers significantly reduce the noise level, while perforated grids can not significantly reduce noise emissions.

As a rule, the maximum noise emission of the machines is not more than 78 dB (A).

Which controls can GHD Hartmann Maschinenbau offer?

In addition to contactor controls for simple devices, GHD Hartmann Maschinenbau offers systems from the manufacturer Omron as a standard controller for more complex tasks.

Siemens or Allen Bradley are available as options.

What is the difference between a fixed blade guide and an adjustable blade guide?

Adjustable blade guides:

 

Negative:

  • Complicated access for cleaning
  • Complicated exchange of guiding pads
  • One position for wearing of pads
  • Correct cleaning would require the dismantling of the both adjustable guides. This requires hours
  • Not according to sanitary demands (local laws and rules)
  • If used in combination with oil the unit might “stick together”

Positive:

  • One system for every slice thickness (if within the adjustable range)
  • Tolerances within the length of loaves are divided to the slice thicknesses

 

Exchangeable blade guides

 

Negative:

  • One set of blade guides per slice thickness required

Positive:

  • Always correct adjustment of slice thickness
  • Fingers could be turned several times in case of wearing
  • Fingers could be easily exchanged in case of wearing
  • Jet-wash cleaning and drying outside the packaging area
  • Good access for cleaning
  • Good access for blade exchange
  • Better visibility of the slicing process

What compressed air quality is recommended for machine use in the food industry?

According to ISO 8573-1 with reference to VDMA standard sheet 15390-2, we specify a compressed air quality that we recommend when using the machines and devices.

How is the blade change performed on a belt cutter?

The slicer band blades are a wearing part of the band cutter. The service life of the slicer band blades varies depending on the type of bread. Usually a complete set of slicer band blades is always changed, as the slicer band blades stretch slightly during use and thus become "longer".

For the slicer band blades change you can disassemble the knife guide for easy accessibility quickly and easily. Depending on the experience, changing a knife set takes about 5-10 minutes

Vollkornbrot-Scheiben
Mischbrot geschnitten
Sesam-Sonnenblumenbrot dunkel
Toastbrot geschnitten

SL 30

Fully automatic band slicing machine for toast and rye mixed bread. The cutting process takes place via heavy duty band knives with a length of 176 inches (about 4.5 m). The total length is tensioned between two hard chromed drums. The self-supporting, torsion-resistant tubular steel frame ensures smooth running of the machine. Generously designed doors and hoods allow both a good cleaning and maintenance access as well as a quick blade change.

Technical specifications

Dimensions: Length: approx. 3145 mm, Width: approx. 1150 mm, Height: 2600 mm
Weight: 1600 kg
Product dimensions: Length: 160 - 400 mm, Height: 50 - 180 mm
Capacity: up to 3800 products /h
Speed of the slicer: adjustable between 180 - 400 m/min
Belt cutter length: 176 inch / approx. 4,5 m
Controller: Omron
Operating panel: Touchscreen
Frequency controller: Hitachi
Pneumatic system: Festo
Power supply: 230/400 Volts / 50 cycles
Power input: approx. 6,5 kW
Compressed air: min. 6,0 bar (ISO 8573-1)
Operating side: left / right
Protection class: IP 54
Adjustment: automatic/ manual